The Impatient Gardener: Our first DIY fail

30 April 2013

Our first DIY fail

Maybe I got too confident about our DIY ability. After all, I've jumped in with both feet to projects I had no idea would work, we installed our bedroom floors, I laid a huge stone path through our yard and built stacked-stone retaining walls and I've even learned how to do some electrical work. Our theory on when to do things ourselves and when to let the pros do the work usually involves deciding if we can do as good (or better, which is often the case) of a job as they can for less money and a realistic amount of time.

So it is humbling to tell you that we have suffered our first official DIY failure with a project that is frequently DIY'd: crown molding.

Our cabinet maker put the crown molding around the top of the cabinets but we told him (with an air of overconfidence) that we'd take care of putting it up in the rest of the room. We read a lot of online tutorials, including this one at Young House Love and another at Sawdust and Embryos. We even bought the Kreg Crown Pro jig (which is now shorter thanks to a misfire with the saw).

After a lot of reviewing of tutorials and reading the jig instructions, we started measuring and cutting. We have two sides to the kitchen, which is divided by a beam down the middle, so we started with the "easy" side where it would be just four pieces of molding and four inside corners. The other side involves a lot more corners because of the cabinets and coping instead of mitered corners.

This is as far as we got. One piece of crown molding that is ultimately going to have to be removed and recut thanks to me cutting the corners incorrectly. 
First we did some sample cuts and spent about an hour trying to wrap our brains around the upside down, backwards and inside out angles involved in crown molding. Once we FINALLY got that down (we had the jig set to the wrong spring angle), we cut. I was operating the saw. Unfortunately I assumed that pushing the bottom part all the way one way or the other would cut a 45-degree angle. Unfortunately I didn't notice that the saw actually went PAST 45 degrees, to about 47 or 48 degrees. I did notice this after we made about three or four cuts. We put up two pieces of crown, attached but just a couple brad nails in case they needed adjusting, and called it quits for the weekend (this was two weekends ago).

When we picked it up this past weekend, we discovered that the two pieces we put up would both have to be recut (I thought I might have screwed up the setting on the saw but we weren't sure). Then there was the issue of adjusting it to fit with its neighbor piece. I suspect that in a house with straight walls would not be as challenging to install crown molding in.

I'm certain we could have figured it out had we persevered. We might have needed another piece of crown molding, but we would have gotten it eventually. But at some point we realized this was in no way fun. And there are times when the phrase "Life's too short ..." comes into play. At some point your frame of mind and your precious weekend time becomes more important than whatever it will cost to pay someone to do this for us.

So we've got a few people to call to bail us out and we'll pay them probably more than we should. But in the end we'll be happier people for having done that. And that's worth its weight in gold.

Because as Kenny Rogers famously sung, sometimes you just have to know when to walk away. And I'm OK with that.

Labels: , , ,

8 Comments:

Blogger Unknown said...

Too funny, Erin. We did exactly the same thing last weekend - total fail on the crown molding we were putting up on the top of our cabinets. We got the first two corners fine, but the rest were a disaster. Used way too much molding (good thing it's cheap) and haven't moved forward with it again. It's tricky stuff - you have to have the molding exactly on the mitre saw perfectly or the corners won't match. Total fail here too. So don't feel alone in this, my friend.

I'm going out to the garden - at least there are no corners to cut there. :-)

April 30, 2013 at 12:09 PM  
Blogger Erin @ The Impatient Gardener said...

Heather, I feel better that we're not the only ones who failed at crown molding! And I'm with you ... the garden is a much more forgiving place.

April 30, 2013 at 3:04 PM  
Blogger Katie @ Team Skelley said...

Crown is deceptively hard. I am not that precise. I tried to add a chair rail to a room once and it went terribly awry.

April 30, 2013 at 4:49 PM  
Blogger Unknown said...

It certainly is!! We have two spans of cupboards in the kitchen - one with crown moulding, one without. And I daren't bring up the subject as my husband is furious that we failed at this.

May 1, 2013 at 6:13 AM  
Blogger jthayerjr said...

Hi Erin,
I re-furburshed an old firewood box and turned it into a toy box for my little girl. I put molding on the "lid" and around the bottom. Lets just say I have a new appreciation for carpenters to say the least ;) Jim

May 1, 2013 at 7:36 AM  
Blogger Erin @ The Impatient Gardener said...

Funny how the most simple looking projects are the ones that bite you, isn't it?

May 1, 2013 at 8:52 AM  
Blogger Erin @ The Impatient Gardener said...

They do make it look simple don't they? But I bet it's all that much more special because you made it for her!

May 1, 2013 at 8:53 AM  
Blogger LINDA from Each Little World said...

I Just had the most major baking failure (and I am a former pastry chef) of my life, so maybe it is something in the air.

May 1, 2013 at 4:38 PM  

Post a Comment

Thank you for taking the time to comment! I appreciate it. I try to respond to comments here or sometimes via email so make sure to check back.

Subscribe to Post Comments [Atom]

<< Home