The Impatient Gardener: Re-doing the kitchen: Part 2

23 February 2010

Re-doing the kitchen: Part 2

R  emember how I got this slightly damaged table for a great deal at the Restoration Hardware outlet? Well, it's been hanging out in our basement waiting for the kitchen project to get on track.

We brought it upstairs and set it up.

 
You might not be able to tell from this picture (ignore the green tape), but there's one little problem: It's too long. You can't easily get in and out of the banquette on the left side. Of course we knew from the beginning that we'd have to cut some of it off because we purchased it with one smushed in corner (and since it's a maple veneer on top of MDF, there's no fixing that).
So you might think, as I did, oh, simple fix ... just cut equally from each end. But alas, you would be, as I was, sorrily mistaken. Because you see, the ends are really great places to sit. There is one foot of table overhang beyond the legs. And the second you make that measurement smaller, your legs are crammed against the table and you lose two places to eat. Isn't this the way all projects go? Any time you start thinking they are simple, be prepared for a big ol' wrench to be thrown in your plan.

This wrench required that "stretcher bar" part of the trestle to be shortened 9 inches, which my hubby did. Don't ask me to tell you how it did it because all I know is that he took up to his dad's workshop and used a variety of tools including a table saw, drill press and something call a forstner bit (which I like to call a forceps bit just to irritate him). 

We then had to cut the table off. I was really nervous about this because if you've ever tried to cut one of those particle board shelf boards, you know how much they tend to chip. We got the finest blade our el cheapo circular saw could handle. Unforunately that was only 40 teeth (everything we read online suggested 60 or 80 teeth), but the guy at the hardware store thought it would be fine. He did give us one good tip though: cut the table upside down because of the way the saw turns.

We measured about 10 times (forget the adage measure twice, cut once, we were going to measure until we are DARN sure we had it right), then clamped on a metal ruler straight edge thing (I'm sure there's a real name for this tool, but couldn't tell you what it was) to serve as a guide for the saw. Then we cut off half the amount we needed. Because we had to move one leg in, we just cut from one side of the table, but we only cut half the amount to make sure the blade was going to work. And it did! There was one tiny little chip at the end though, so on our second cut—the REAL cut—we taped the area where the veneer would be cut. It worked like a charm ... a perfect cut!

 

We'll still have to re-veneer the cut but we have to find some edge banding first. Stay tuned for that part of the project.

Here's the freshly cut end (on the still upside-down tabletop).


The new length of the table is great. You can now comfortably get in and out of either side of the banquette and we figure we can fit seven adults and even more if we're squeezing or you throw a few kiddos in the mix.

There, isn't that better?
 

The chairs are leftover from the old table but I think they'll work out just fine, because as you might have guessed ... I'm not done with this table yet. Stay tuned.

If you want to see where this little mini kitchen re-do began, click here.

6 Comments:

Blogger Remington said...

Perfect fit! AND it looks great!

February 23, 2010 at 7:50 AM  
Blogger Kasey at Thrifty Little Blog said...

Wow, I'm so impressed with your thrifty find and diy skills. Most people end up keeping the too large or too big pieces in their homes. Now you practically have a custom piece!

February 23, 2010 at 2:57 PM  
Blogger Melissa @ The Inspired Room said...

Wow, that is an amazing project. I love it!

I like that you got a great deal and found a solution to make it work for you!

February 24, 2010 at 10:30 AM  
Blogger LINDA from Each Little World said...

Looking good! And you are so right about easy projects; no such thing. As for cost: projects are under $100 or then seem to jump immediately to $500. I am impressed with all the thinking and planning you did, once you knew the challenges to be surmounted.

February 24, 2010 at 8:39 PM  
Anonymous Anonymous said...

that looks alot better good job

February 28, 2010 at 9:02 PM  
Blogger Brigitte said...

That is a beautiful table! Great find and mod to make it work. I need to do something like this because we just moved this past summer. Our table that was a perfect fit at the old house is majorly cramped in the new one and is blocking the french door access to the backyard. This would really help make some more space.

I was wondering if you wouldn't mind sharing the dimensions of your banquette, particularly the depth of the seat, height before cushions, and thickness of the cushions. How far away from the edge of the banquette is the table if that makes sense? I am trying to figure out how big I can make ours without going so big that it's cramped with people having to climb into the seat.

Do you find the seat to be comfortable enough with the pillows for back support and flat seat or do you wish you had done some angles like I'm seeing on some DIY booth/banquette tutorials? Do you find the two pedestal base on the table to be an issue getting in and out of the banquette? Our current table has 4 legs, which I think will be a pain and will be replaced. Sorry for so many questions. What you've done would be perfect in my house. Thank you for your post!

February 9, 2012 at 12:17 AM  

Post a Comment

Thank you for taking the time to comment! I appreciate it. I try to respond to comments here or sometimes via email so make sure to check back.

Subscribe to Post Comments [Atom]

<< Home